Haynes Manuals Home

Search:

Type: Posts; User: BroncoJoe19

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    1,115

    I pulled codes and in the past week, I had two...

    I pulled codes and in the past week, I had two cylinder misfire codes, my car has 150,000 miles on it and starting at about 90K once in a while a I'd get a missfire and replaceing that cylinder's...
  2. Replies
    6
    Views
    6,725

    Dano, IF the starter won't crank the engine when...

    Dano,
    IF the starter won't crank the engine when it is cold, but will crank the engine when it is warm, assuming that your terminals and connections are clean, then you need to replace the battery....
  3. Replies
    2
    Views
    855

    Did you check your fuel inertia saftey switch?...

    Did you check your fuel inertia saftey switch?
    The red button should be depressed.

    With the key in the ON position, check to see if you have 12 volts at the pump, check your ground at the pump.
  4. Replies
    2
    Views
    980

    Franklin, I check my fuses with a...

    Franklin,
    I check my fuses with a voltmeter/continuity tester.

    cherokee,
    Franklin is correct about the VSS. Vehicle Speed Sensor.
    At least in full size broncos the VSS was in the transfer case...
  5. I agree with muddy cherokee Check your...

    I agree with muddy cherokee
    Check your connections, with that old a truck your grounds may be bad.
    If they check out fine, then look in your manual wireing diagrams and see if it uses fuseable...
  6. Thread: pinout II

    by BroncoJoe19
    Replies
    3
    Views
    1,974

    Grim, I probably shouldn't **** in here.. but is...

    Grim,
    I probably shouldn't **** in here.. but is your car OBDII complient, was it manufactured in 1996 or later?
    I'm familiar with some Fords. Mostly they allowed one to use a jumper to flash codes...
  7. Replies
    2
    Views
    1,115

    4.6L Coil on Plug resisstance values?

    Hi I have a '99 Crown Vic with the 4.6L engine, and coil on plug distributorless ignition system. I assume the primary fields should be 0.3 to 1.00 ohms, what should the range of resisstance values...
  8. I don't know why the above link didn't work...

    I don't know why the above link didn't work
    Perhaps this will work.



    <A...
  9. I obtained the information regarding the pinouts...

    I obtained the information regarding the pinouts for the GEM from another source. Here is a little testing proceedure I put together that others my find useful.
    ...
  10. Having the pinouts of those three connectors...

    Having the pinouts of those three connectors would be helpful. From there one could do a lot of troubleshooting.

    I disconnected the connectors and back probed the black/pink wire and checked for...
  11. I don't think that is the schmatic/diagram for a...

    I don't think that is the schmatic/diagram for a '98 windstar. I pulled the front cover off and took a couple of pictures. According to this diagram the PCM should be to the left of the fuse box, but...
  12. This is what they sent me, but I still could not...

    This is what they sent me, but I still could not find it, any additional help would be appreciated.
  13. Do you have a picture of it?

    Do you have a picture of it?
  14. Replies
    3
    Views
    1,883

    My ABS light was on, and when I had it in the...

    My ABS light was on, and when I had it in the shop for air conditioning, I asked the mechanic if he had an ABS scanner. He told me it was the VSS on the rear. Later I noted the light was out, so...
  15. Hi Admin, Thanks for the response, but I was not...

    Hi Admin,
    Thanks for the response, but I was not able to find it. Do you have a picture of it?
  16. Replies
    3
    Views
    1,883

    1999 Ford motor home VSS/ABS

    Hi I just picked up a new VSS for my '99 Ford motor home. It mounts to the top of my rear diff. The mounting hole is not round, but rather it is oblong or oval. Does one have to adjust the sensor as...
  17. Yes, I am sure that will be very helpful. Thank...

    Yes, I am sure that will be very helpful.
    Thank you very much! :)
  18. Replies
    2
    Views
    1,753

    I have a '99 Ford motor home and picked up a new...

    I have a '99 Ford motor home and picked up a new VSS. The bolt hole for it is oblong. Does it need to be adjusted when installed? IF so... how?
    Thanks so much.
  19. Ford Windstar "Generic Electronic Module" and Door ajar

    I have a '98 Ford windstar.
    The wiring diagram depicts a "Generic Electronic Module" That has wires that go to each of the door ajar switches.

    Where is the "Generic Electronic Module" located?
    ...
Results 1 to 19 of 19