Haynes Manuals Home
Tab Content
No Recent Activity

24 Visitor Messages

  1. View Conversation
    Mike, I just tried to post something and it said I did not have permission. I just created a profile/login and got an email saying welcome. Am I supposed to do something else?

    I have a Haynes manual and there is a big mis-print in this one which took me several months to figure out.

    Regards,

    Pat
  2. View Conversation
    Hi, Mike!!! Please help! Does Haynes or anybody make a repair maual for the '05 & '06 Jeep Liberty CRD/Diesels? We have 2 and love them....but can't find any manuals on them. Thanks. Doug
  3. View Conversation
    hi, mike
    i've unsnapped locking r8ing on driverside door main wiring trunk.
    plug wont come out.95jeep gr cher
  4. View Conversation
    95 jeep grand cherokee ,manualpp, 11-11
  5. View Conversation
    (I'm posting my question everywhere as I'm new to this "forum"s stuff. Did not know where to post.)

    Honda Accord 2001 F23A1 engine

    --------------------------------------------------------------------------------

    I'm assembling the crankshaft area of my Honda Accord EX 2001, 4 cyl. and the manual does not list the torque spec for the outer main cap bridge bolts. It shows only Main Caps: Step 1@22ft/lbs, Step 2@58ft/lbs. I doubt the 10MM outer bolts get torqued at this same number.

    Please reply with the torque spec for the outer main cap bridge bolts. Thanks.
  6. View Conversation
    Hello Mike,
    I am currently working on a 1990 Chrysler Lebaron 2 door convertible with a 2.5 liter engine. It is front wheel drive and is not turbo charged. I am changing out the aluminum head. I have installed new head bolts. But the torque specs have me concerned.
    I would like a verification on the head bolt torque specs. The book I have has a 4 torque sequence in it. What concerned me is whether we are talking about all ft. lb torque specs. or are the two "65" numbers mentioned in step 2 and 3 angle torque degree references. Please advise accordingly
  7. View Conversation
    Hi, I have a question; if i replace a compressor on a 06 town&country will i need to recharge the a.c.?
  8. View Conversation
    i have a 93 chev van with 350 in it . i need to find out were the knock sencer is located can,t seem to find it. do,ent show me in the haynes manual
  9. View Conversation
    I have a 1981 Ford Bronco with a 5.0L 302 and I am having an issue where it idles fine, and throttles fine in park/neutral, but when I put it in drive, and press on the gas it stumbles a second and then picks back up, but doesnt go anywhere fast at all. usually takes about 1/4-1/2 mile just to get to 45 and anything over that is nearly impossible!

    already checked for rich mixture, fuel lines, etc!
  10. View Conversation
    Hi Mike! I have a 1996 Chev Astro Van V-6 Vortec and there has been some discussion with my son about what the engine size is--3.5 or 4.3. Can you fill me in on some details please?
Showing Visitor Messages 11 to 20 of 24
Page 2 of 3 FirstFirst 123 LastLast
Page 2 of 3 FirstFirst 123 LastLast
About Mike F

Basic Information

Statistics


Total Posts
Total Posts
120
Posts Per Day
0.03
Visitor Messages
Total Messages
24
Most Recent Message
09-23-2012 04:45 AM
General Information
Last Activity
12-01-2016 06:38 PM
Join Date
10-12-2007
Referrals
0